esp-idf-st7789

ST7789 Driver for esp-idf

The demo video by Dmitry Andreev.
https://www.youtube.com/watch?v=aOyaK0pUiPk&t

Software requirements

ESP-IDF V4.4/V5.x.

Installation for ESP-IDF V4.4

git clone -b v4.4 https://github.com/nopnop2002/esp-idf-st7789
cd esp-idf-st7789/
idf.py set-target {esp32/esp32s2/esp32s3/esp32c3}
idf.py menuconfig
idf.py flash

Note for ESP32-S2
The tjpgd library is not included in the ESP32-S2 ROM because the ROM of the ESP32-S2 is small.
Therefore, JPEG files cannot be displayed.

Note for ESP32-C3
For some reason, there are development boards that cannot use GPIO06, GPIO08, GPIO09, GPIO19 for SPI clock pins.
According to the ESP32-C3 specifications, these pins can also be used as SPI clocks.
I used a raw ESP-C3-13 to verify that these pins could be used as SPI clocks.

Installation for ESP-IDF V5.x

git clone https://github.com/nopnop2002/esp-idf-st7789
cd esp-idf-st7789/
idf.py set-target {esp32/esp32s2/esp32s3/esp32c2/esp32c3/esp32c6}
idf.py menuconfig
idf.py flash

Note for ESP32-S2/ESP32-C2
The tjpgd library is not included in the ESP32-S2/ESP32-C2 ROM.
However, you can use this IDF component registry.
JPEG files can be displayed.

Note for ESP32-C6
ESP-IDF V5.1 is required when using ESP32-C6.

Configuration

Generic ST7789 1.3 Inch

There is 2 kinds of marking.
The pin marking is written as SCL/SDA, so it looks like i2c, but it is SPI.
SCL is SCLK, SDA is MOSI.

MISO is not use.

BMP file

JPEG file(ESP32/ESP32S2/ESP32C3)

PNG file

QR-CODE

Generic ST7789 1.14 Inch

Generic ST7789 1.9 Inch

Generic ST7789 2.0 Inch

SPI Clock speed

According to the ST7789 datasheet, the minimum SPI clock cycle time is 16ns.
Therefore, the maximum SPI clock frequency is 62.5MHz.
The SPI clock frequency used by this project is 20MHz.
Higher SPI clock frequencies can be specified using spi_clock_speed().
When using higher SPI clock frequencies, you need to be careful about the length of the wire cable.

    //int speed = 40000000; // 40MHz
    int speed = 60000000; // 60MHz
    spi_clock_speed(speed);
    spi_master_init(&dev, CONFIG_MOSI_GPIO, CONFIG_SCLK_GPIO, CONFIG_CS_GPIO, CONFIG_DC_GPIO, CONFIG_RESET_GPIO, CONFIG_BL_GPIO);
    lcdInit(&dev, CONFIG_WIDTH, CONFIG_HEIGHT, CONFIG_OFFSETX, CONFIG_OFFSETY);

• Benchmarking using ESP32 & 1.3 inch TFT Without Frame Buffer.
  Clock up has little effect.

	20MHz	40MHz	60MHz
FillTest	1150	1090	1090
ColorBarTest	50	50	50
ArrowTest	280	250	250
LineTest	2190	2150	2150
CircleTest	1940	1910	1910
RoundRectTest	1980	1940	1940
DirectionTest	450	430	430
HorizontalTest	1070	1040	1040
VerticalTest	1070	1040	1040
FillRectTest	190	150	150
ColorTest	260	220	220
CodeTest	1070	1040	1040
BMPTest	7160	7130	7130
JPEGTest	2550	2530	2530
PNGTest	2850	2830	2830
QRTest	220	170	170

• Benchmarking using ESP32 & 1.3 inch TFT With Frame Buffer.
  The effect of clocking up varies depending on the test case.

	20MHz	40MHz	60MHz
FillTest	1150	1090	1090
ColorBarTest	70	50	50
ArrowTest	60	30	30
LineTest	50	30	30
CircleTest	60	30	30
RoundRectTest	50	30	30
DirectionTest	70	50	50
HorizontalTest	70	40	40
VerticalTest	70	40	40
FillRectTest	60	30	30
ColorTest	60	30	30
CodeTest	100	80	80
BMPTest	7490	7470	7470
JPEGTest	2550	2530	2530
PNGTest	2850	2830	2830
QRTest	120	100	100

SPI BUS selection

The ESP32 series has three SPI BUSs.
SPI1_HOST is used for communication with Flash memory.
You can use SPI2_HOST and SPI3_HOST freely.
When you use SDSPI(SD Card via SPI), SDSPI uses SPI2_HOST BUS.
When using this module at the same time as SDSPI or other SPI device using SPI2_HOST, it needs to be changed to SPI3_HOST.
When you don't use SDSPI, both SPI2_HOST and SPI3_HOST will work.
Previously it was called HSPI_HOST / VSPI_HOST, but now it is called SPI2_HOST / SPI3_HOST.

Using Frame Buffer

When FrameBuffer is enabled, all output will be stored in the internal FrameBuffer and reflected to the device with lcdDrawFinish.
If you don't use FrameBuffer, lcdDrawFinish does nothing.
If your main purpose is to display text, it's well worth using FrameBuffer.
If your main purpose is to display images, there is no value in using FrameBuffer.
Enabling FrameBuffer does not make image display faster.
This is because image analysis takes time.
ESP32C2 has too small memory to use this function.
Note that using FrameBuffer consumes memory.

If your SoC has PSRAM, you can avoid running out of memory by enabling PSRAM.
ESP32S2 has less RAM, but some ESP32S2 have PSRAM.

Benchmarking using ESP32 & 1.3 inch TFT

	Without Frame Buffer	With Frame Buffer
FillTest	1150	1150
ColorBarTest	50	70
ArrowTest	280	60
LineTest	2190	50
CircleTest	1940	60
RoundRectTest	1980	50
DirectionTest	450	70
HorizontalTest	1070	70
VerticalTest	1070	70
FillRectTest	190	60
ColorTest	260	60
CodeTest	1070	100
BMPTest	7160	7060
JPEGTest	2550	2550
PNGTest	2850	2840
QRTest	220	120

LILYGO TTGO 1.14 Inch ESP32

LILYGO TTGO T8 ESP32-S2

Custom PCB

Details can be found here.

JPEG Decoder

The ESP-IDF component includes Tiny JPEG Decompressor.
The document of Tiny JPEG Decompressor is here.
This can reduce the image to 1/2 1/4 1/8.

PNG Decoder

The ESP-IDF component includes part of the miniz library, such as mz_crc32.
But it doesn't support all of the miniz.
The document of miniz library is here.

And I ported the pngle library from here.
This can reduce the image to any size.

Font File

You can add your original fonts.
The format of the font file is the FONTX format.
Your font file is put in font directory.
Your font file is uploaded to SPIFFS partition using meke flash.

Please refer this page about FONTX format.

Font File Editor(FONTX Editor)

There is a font file editor.
This can be done on Windows 10.
Developer page is here.

This library uses the following as default fonts:

• font/ILGH16XB.FNT // 8x16Dot Gothic
• font/ILGH24XB.FNT // 12x24Dot Gothic
• font/ILGH32XB.FNT // 16x32Dot Gothic
• font/ILMH16XB.FNT // 8x16Dot Mincyo
• font/ILMH24XB.FNT // 12x24Dot Mincyo
• font/ILMH32XB.FNT // 16x32Dot Mincyo

From 0x00 to 0x7f, the characters image of Alphanumeric are stored.
From 0x80 to 0xff, the characters image of Japanese are stored.
Changing this file will change the font.

How to build your own font file

step1)
download fontxedit.exe.

step2)
download BDF font file from Internet.
I downloaded from here.
fontxedit.exe can ONLY import Monospaced bitmap fonts file.
Monospaced bitmap fonts can also be downloaded here.

step3)
import the BDF font file into your fontxedit.exe.
this tool can convert from BDF to FONTX.

step4)
adjust font size.

step5)
check font pattern.

step6)
save as .fnt file from your fontedit.exe.

step7)
upload your font file to $HOME/esp-idf-st7789/fonts directory.

step8)
add font to use

FontxFile fx32L[2];
InitFontx(fx32L,"/spiffs/LATIN32B.FNT",""); // 16x32Dot LATIN

Font file that From 0x80 to 0xff, the characters image of Japanese are stored.

Font file that From 0x80 to 0xff, the characters image of Latin are stored.

How to add your color

Change here.

#define RED    rgb565(255,   0,   0) // 0xf800
#define GREEN  rgb565(  0, 255,   0) // 0x07e0
#define BLUE   rgb565(  0,   0, 255) // 0x001f
#define BLACK  rgb565(  0,   0,   0) // 0x0000
#define WHITE  rgb565(255, 255, 255) // 0xffff
#define GRAY   rgb565(128, 128, 128) // 0x8410
#define YELLOW rgb565(255, 255,   0) // 0xFFE0
#define CYAN   rgb565(  0, 156, 209) // 0x04FA
#define PURPLE rgb565(128,   0, 128) // 0x8010

External input module

You can use these if you need some input.

• MPR121 Capacitive Touch switch
  https://github.com/nopnop2002/esp-idf-mpr121

• TTP229 Capacitive Touch switch
  https://github.com/nopnop2002/esp-idf-ttp229