BMBurner is a Arduino based EPROM Programmer SST 27SF512, 27C256, 27C512, 27SF256, 29C256, W27E512, W27C512, DS1230, 62C256, etc..
BMBurner is a Arduino based EPROM Programmer that can Read/Write/Verify Chips (27C256, SST 27SF512, W27E512, etc...)
If you have a BMBurner v2.5 or above, you must 'jump' the jumper nearby the Power Switch with a paperclip (by exemple) and at the same time than you are clicking on the 'Update Firmware' button otherwise the firmware won't install in the BMBurner
*** Image may differ from the updated tool ***
Command | Receice Buffer | Description |
---|---|---|
'C'+R+'S'+'MSB'+'LSB'+'CS' | "B1"+"B2"+"...BX"+"CS" | Reads 'S' bytes(S=Size, S=0 for 256bytes) from the EEPROM at address 'MSB'+'LSB' (C=Chip, C=2 for 27C256, C=5 for 27SF512 SST) |
'C'+W+'S'+'MSB'+'LSB'+'B1'+'B2'+'...BX'+'CS' | "O"(0x4F) | Writes 'S' bytes(S=Size, S=0 for 256bytes) from the EEPROM at address 'MSB'+'LSB' (C=Chip, C=2 for 27C256, C=5 for 27SF512 SST) |
5+E+'CS' | "O"(0x4F) | Erase all the data on Chip Type 5 (SST) |
6+E+'CS' | "O"(0x4F) | Erase all the data on Chip Type 6 (SST 256) |
V+'CS' (V+V) | "B1"+"B2" + "B3" | Prints the version bytes of the BMBurner PCB Board for Moates Compatibility(Ex:V5.1.0) |
F+'CS' (F+F) | "B1"+"B2" | Prints the firmware bytes of the BMBurner PCB Board(Ex:V2.0) |
G+'CS' (G+G) | "B1"+"B2" | Prints the BMBurner Starting baudrate (Ex:'B1=1,baud 921.6k', 'B1=2,baud 9600', 'B1=3,baud 115200') |
S+0+S | "O"(0x4F) | Switch the internal baudrate on the BMBurner to 921600 for Moates Compatibility |
S+7+S | "O"(0x4F) | Switch the internal baudrate on the BMBurner to 115600 for Moates Compatibility |
A+'N' | "O"(0x4F) | Change the chip AccessTime to 'N'ns (Ex:N=70 for 70ns AccessTime) |
Command | Descriptor |
---|---|
'N' | 'N' equal the AccessTime in ns (Ex:N=70 for 70ns AccessTime) |
'MSB' | 'MSB' equal to the Most Signifiant Byte for the EEPROM Address location |
'LSB' | 'LSB' equal to the Least Signifiant Byte for the EEPROM Address location |
'C' | 'C' equel the Chip Type (C=2 for 27C256, C=5 for 27SF512 SST, C=6 for 27SF256 SST, etc..) |
'S' | 'S' equal the Size/Amount of bytes to proceed (S=0 is for 256bytes else S equal the amount of byte, S=1 for 1byte) |
'CS' | 'CS' equal to the checksum of the Commands we are sending in 1Byte form |
... | Any Command that isn't within 'Brackets' are the actual Char/String to send (ex: V is for sending the Char V |
You can donate to me using This Link.