ADVi3pp Versions Save

ADVi3++, an alternative and better firmware for Wanhao i3 Plus printers and clones. Fork of Marlin Firmware.

advi3++5.8.0

2 months ago

This release has major fixes. In particular, following messages in this community, I found that the X-Twist compensation feature was completely broken. There were also issues with homing (G28), and incorrect flow rate during Extruder Tuning.

The complete list of changes is the following:

advi3++5.7.0

10 months ago

This release has important fixes and new features. In particular, it now supports a BLTouch sensor with Mark II printers. See the announcement for more information.

The complete list of changes is the following:

#332 - SD card sorting is not working as expected bug
#329 - Add a way to cancel Load and Unload filament enhancement
#327 - For Mark II printers, select by default the Mark II offsets for the probe enhancement
#326 - Synchronise sources with Marlin 2.1.2 enhancement
#322 - Save the last temperature used to Load/Unload and restore it on boot enhancement
#319 - Use Touch Switch Mode (SW) for BLTouch enhancement
#315 - Beep in Preheat when the target temperature is achieved enhancement
#314 - Apply the setting under Settings / Beeper / Beep duration to M300 without P argument enhancement
#262 - Add BLTouch support for i3 plus Mark II enhancement
#115 - Allow Temp Change during filament change enhancement

advi3++5.6.0

1 year ago

#330 - Specific sequence leads to catastrophic failure
#328 - For some users, Homing X, Y or Z is stuck on the "Homing..." screen

advi3++5.5.1

1 year ago

advi3++5.5.0

1 year ago

#318 - Thermal runaway error is not always displayed on the LCD screen
#317 - G-Code M114 response breaks Octolapse
#313 - Cancel automatic leveling
#312 - Detect and prevent bounces
#311 - Restore Z-offset in Sensor Settings
#310 - Add steps in BLTouch Tuning for cases when the BLTouch is blinking red
#308 - Update description of Print Settings pane
#307 - Versions over 5.0.3 having issues accessing SD card files
#306 - Fast probing with BLTouch
#293 - BLTouch - warning on transposed black and white wires
#296 - Manual jog controls disturb homing function, triggering "Homing failed" hardware error
#294 - If print menu is accessed while printer is moving, it shows as if it's printing
#267 - Live Flow Tuning
#238 - M851 should accept all offset arguments, not just Z offset
#153 - Graph as default view or GCode to show the graph view

advi3++5.4.2

1 year ago

#298 - The computation of the Extruder Tuning is wrong
#297 - The firmware does not take into account arguments for the M300 code
#293 - BLTouch - warning on transposed black and white wires

advi3++5.4.1

1 year ago

#292 - LCD and beeper settings are not saved or taken into account

advi3++5.4.0

1 year ago

#291 - When pressing on a move button, it continues for a while after the button is released
#290 - Avoid homing when not necessary
#289 - Travel movements during manual bed levelling significantly slower than earlier versions
#288 - Inversion of black and white BLTouch wires not detected
#287 - Warn if manual bed leveling is attempted while extruder is hot
#285 - Show what triggered a hardware error
#284 - LCD stuck dim when hardware error detected
#279 - Enhance the beeping feature
#277 - Raise extruder during Tuning / Extruder
#274 - Enhanced motion during filament load
#246 - Skew compensation implementation
#177 - Cancel e-steps tuning

advi3++5.3.0

2 years ago

#214 -Troubleshooting vibrations and mechanical issues

advi3++5.2.0

2 years ago

#278 - Hide gcode files where the file name starts with a period
#276 - Files with the letter “å” in the file name do not appear correctly
#21 - Implement file management
Change slightly the font on the LCD panel